+86 18988945661 
contact@iflowpower.com 
+86 18988945661
Language
+86 18988945661 contact@iflowpower.com +86 18988945661
Author ：Iflowpower – Portable Power Station Supplier
The battery / battery is the power source of electric bicycles, so that the battery maintains a good working condition, extending its service life, and has a lot of practical value regardless of environmental or economic perspective. Hey, easy power supply technology reminds you the following is some of the use maintenance methods of the battery: 1. Electric vehicles from the new purchase should be fully charged.
Because many electric cars have been put on hold for a few months, even more than half a year, so it is necessary to use it first, it is best not to use it immediately, you need to stand for about ten minutes. 2, the battery takes down to charge, when installing, the battery is installed firmly on the electric bicycle, and the battery is damaged when the ride is riding. Battery in handling, disabled, roll over, heavy pressure.
3, often clear the dust, dirt on the battery cover, pay attention to keep the battery dry, clean, and discharge the battery. 4, definitely can't make the battery last in a state of low power, and develop a good habit of charging the battery every night. Long-term use, it should be charged, placed in a cool and dry place, charging regularly (general 10 days).
5. Prevent the battery for a long time from being discharged, and the internal structure of the battery is greatly damaged. When the electric bicycle is just started, it is assisted to help start with the foot (unfootable way to push the ground), each starting time cannot exceed 5 seconds.
To start twice, the intermediate interval is 10-15 seconds. When I was uphill, I used the foot to help the electric car on the slope, so as not to excessively changed the battery. 6.
When the battery is used, it should prevent over-discharge, and the battery is discharged to the termination voltage, continues to discharge it is called over-discharge. When riding, pay attention to not allow the battery to be discharged, and the over-discharge is easy to cause a serious loss of the battery, which greatly shortens its service life. Therefore, the battery should be used to prevent depth discharge, and it should be shallow, and the general situation should be done: the battery will charge the best in the battery with a depth of discharge.
In addition, since the electrop pressure is controlled by the controller, other devices such as voltages other than the controller, such as voltmeter, and the power consumption of the indicator light are directly powered by the battery, and the supply of the power source is generally not controlled by the controller. Once the electric car lock switch begins to use electricity. Although the current is small, if it is discharged for a long time to discharge, it will appear.
Therefore, you can unlock it for a long time, it should be turned off immediately. 7, prevent over charge, stop charging when the charger is filled, can not charge for one night or even a few days. Overcharge can cause a plate active material hardening and deformation of water and battery.
When the battery discharge depth is relatively large, the charging time should be shortened when the ambient temperature is high. Also choose the charger parameters to match the battery, so it is necessary to fully understand the operating conditions of the battery in the high temperature season, and changes during the service life. Do not place the battery in an overheating environment during use, and the installation position of the battery should ensure good heat dissipation, especially when charging, it should be kept from the heat source, and it should stop charging when superheat.
After the battery is hot, he will take cooling measures, and the battery temperature can be charged when the battery temperature is restored. 8, prevent long-term loss, long-term losses will cause plate vulcanization. In the case of low temperature, there is a problem of poor charging and insufficient charging due to insufficient charging.
Insulation and antifreeze measures should be taken at low temperatures, especially when charging should be placed in a warm environment, which is beneficial to ensure sufficient electricity, prevent the occurrence of irreversible sulfate, and extend battery life. 9. Prevent short circuits, should be particularly careful when installing or use, the tools used should take insulation measures.
When connecting the battery, the electrical appliance other than the battery should be connected, and the inspection is not short-circuit, and finally the battery, the wiring specification is in good condition, Preventing overlapping. It is forbidden to use battery short circuit to detect the battery of the battery to prevent accidents from exploding. When the battery is short-circuited, the short circuit current can reach hundreds of amps.
There will be a lot of calories in all connecting parts. It will be fused at the weakness of the weak link; the connection is brought; the battery is partially possible to be in chargeless gas or charging. The explosion, sparks occur when the connection is blown, causing the battery explosion; if the battery short circuit is shorter or the current is not particularly large, it may not cause the connection to blow up, but the short circuit will still have overheating phenomena, which will damage The binder around the connecting strip keeps the leakage.
Therefore, the battery is definitely not short-circuited. 10. Prevent sunlight in the sun, sunlight will increase the temperature of the battery, and the activity of the active substances of the battery will increase, affecting the battery life.
Copyright © 2023 iFlowpower - Guangzhou Quanqiuhui Network Technique Co., Ltd.
