UPS power supply built-in battery how to solve it?

　　Author ：Iflowpower – Portable Power Station Supplier

How does the UPS power supply built-in battery have solved? The battery is factory-parted, and after a long time storage, the battery will also be part of the self-discharge loss. If the UPS power battery that is just replaced is completely unable to discharge, this battery must have a problem. When you touch the UPS power battery, what should I do if I don't supply power to the device? Don't worry, Xiaobian immediately came to answer your questions.

The difference between the UPS power supply external battery and the built-in battery: the biggest difference between built-in batteries and external batteries is that one battery is in UPS, one outside UPS. The built-in battery is integral with the UPS. Since the general UPS volume is small, the battery capacity contained in it is generally small, and it is also very small to expand the battery pack.

External battery, like the name, is outside, not integrated with UPS. Generally it will have a stand-alone battery cabinet, which generally uses an external battery's UPS power battery power. Its battery pack can be applied to battery pack capacity according to the power supply time, or the number of battery packs has reached extended power.

Objective, the battery you say here is generally a battery. How to solve the UPS power supply built-in battery? UPS power battery power consumption. If there is no reaction, it should be repaired.

Xiaobian has the following recommendations: 1. It is recommended that you charge the original charger. 2.

There are many power consumption, and the charging is slow. 3. Power on charging, usually take the rush, as long as you pay attention: Don't use the amount of light and not to charge overnight, these two points remember.

4. Normal impression is completely recycled, basically use the power to 20% or less, then charge the power. This process of Jingshan Battery will prompt, according to the prompt operation.

The UPS power supply battery is independently: 1. Before installation, use a multimeter to check the UPS power battery single-section voltage, to reach the normal voltage of the standard, if there is a battery voltage too low, can cause the entire set of batteries to discharge. 2, use the multimeter to check if the positive and negative poles of the UPS battery are connected correctly, the wrong connection does not voltage, the battery pack is positively connected to the UPS wiring exhaust battery input terminal, the battery pack negative electrode UPS wiring exhaust battery input end negative electrode.

Does the installation process tighten the battery connection wire screw, take the wrench to check if there is no looseness, confirm that the screw is tightened. 3, check if the UPS has a neutral line, some UPS power battery belt neutral lines, the neutral line is the positive or negative electrode of the battery of the battery in the middle of the battery pack to receive the positive and negative intermediates of the UPS wiring battery input terminal. Need to connect the neutral line to reach the battery pack discharge.

4, the number of batteries and the total voltage need to meet the requirements of UPS to charge and discharge. 5, there is a little detail, the battery cabinet DC circuit breaker can also be replaced for a long time, so as not to cause short circuits that cause the battery pack to fail to measure voltage charge. Finally, pay attention to each detail, re-check it, find out the UPS power battery problem root reference to the above steps to resolve processing.

Can the UPS uninterruptible power supply still work properly? If the battery is dead, there is no connection to the input AC power supply, the UPS power supply will definitely not work properly. The UPS itself is just an AC power device, and the battery is the source of electrical energy, such as after the AC is powered off, it can only rely on battery to supply load equipment. Therefore, in the case of normal market, UPS can work properly without the battery, and the UPS will function as a rectification filter.

And after the electricity is powered on, the UPS power can only rely on the battery to power the device. How to extend UPS power storage battery life? You cannot connect different capacities, different properties, and different manufacturers, otherwise it may have a bad impact on the entire set of batteries. Regular inspection and maintenance of the UPS battery appearance is intact, there is a shell deformation and leakage; pole column, the safety net is surrounded by acid mist overflow.

Prevent battery short circuit or depth discharge, the deeper the discharge depth, the shorter the recycle life of the battery. During the discharge transfer process, the discharge capacity of the battery can generally reach 50% of the battery rated capacity. Whether it is in the floating operation status or charging, discharge inspection test status, there is a need to ensure voltage, current meets the requirements.

The voltage is too high or current may cause the battery thermal out of control or loss of water, voltage, and the current will cause battery losses. It will affect the battery life, the voltage is too large or the excessive effect will be more. The above is the solution for the UPS power supply built-in battery.

Today's UPS system is highly intelligent, and uses no maintenance battery, easy to use; use the process or more attention to ensure safe use. .