UPS power battery charging discharge knowledge

2022/04/08

  Author :Iflowpower – Portable Power Station Supplier

The UPS power battery is often used in our lives, so how to charge the discharge, this article will introduce you. First, regarding the UPS power supply battery charging 1. When the UPS floats charge, use the charging voltage 2.

275V / single-single, and calculate current charging or 0.002ca or less. When the temperature is 0c or more or more, it is necessary to correct the charging voltage, with 20C as a starting point per change, single voltage change-3mv.

2. When the temperature is charged or more than 35 ¡ã C or more, the temperature is started at 20 ¡ã C, each change, one recharge voltage adjustment -4mv / single. 3, charging initial current control below 0.

25CA. 4, the amount of charge is set to 100-120% of the amount of discharge, but the ambient temperature is below 5c, set to 120-130%. 5, the lower the temperature (5c or less) The longer the charging end time, the higher the temperature (35C or more), the easier overcharge, so, especially during cycling, charging is performed in 5c ~ 30c.

6. To prevent overcharge, install the charging timer, or automatically convert to a trickle charging method. 7.

When charging, the battery temperature should be controlled within the range of -15c ~ + 40c. 2. Control the battery temperature in the range of -15 ¡ã C - + 50 ¡ã C regarding the UPS power supply battery discharge.

Continuous discharge current is controlled below 3CA (h controlled below 6CA). The discharge termination voltage varies depending on the size of the current, substantially as follows. Pay attention to the press, the voltage is not lower than the following voltage.

Remove quickly after discharge. If you accidentally charge it, please charge it immediately. Third, when installing the battery When installing the battery, please be sure to follow: 1, do not install the battery near the sealed space or fire, otherwise there is a danger that caused explosion and fire.

2, do not use the ethylene film, there is a possibility of static electricity, and sometimes explosions sometimes caused by static electricity. 3, do not install the battery in places where possible into the water, otherwise there is an electric shock, the danger of fire. 4, please do not install the battery in more than -40 ¡ã C ~ 60 ¡ã C.

5, do not use the battery in a dusty place, otherwise it is possible to cause battery short circuit. 6. When putting the battery in the box, pay attention to air circulation.

7, do not have sticky or label objects to press the upper cover, due to the exhaust valve below the upper cover, the gas generated in the battery will not escape. 8, when the number-floating charge, the plug-in terminal battery can only be associated with three columns, and the bolt fastening terminal is not particularly limited, but the inclusion of the parallel number of small reliability. In addition, when connected to the line, it is necessary to consider that the wiring conductor and contact resistance between the columns are equivalent, in order to keep each column charge and discharge battery balance, please do not exceed three columns in actual use.

9. At the same time, the use capacity is different, the new is different, when the battery is different, due to the difference in characteristics, it is possible to damage the battery and machine, so avoid use. Fourth, regarding UPS Power Battery Storage 1, please pay attention to the temperature exceeding the range of -20 ¡ã C ~ + 40 ¡ã C.

2, the battery must be kept in a fully charged state when the battery is kept. If you lose a part of the capacity due to self-discharge during transport or during storage, please add electricity. 3, long-term storage, to make up for the self-discharge during the storage, please make supplement.

When kept in more than 40C, there is a bad impact on the battery life, please avoid! 4, please keep the low temperature and well ventilated place. 5. If the battery pack is inadvertently wet during the storage or transfer process, the wet carton should be removed immediately to avoid the wet carton that is wet, causing a conductor to cause battery discharge or burn the positive terminal.

5. About UPS Power Battery Daily Inspection and Maintenance 1, regularly check the battery, if it finds that dust is contaminated with dust, please clean with water or warm water. Do not use organic solvents such as gasoline, banana water or oil, and avoid using chemical fiber cloth.

2, when the floating charge, the indicator value of the total voltage or indicator disk during battery charging is deviated from the base value (¡À 0.05V / mononegery) as shown in the following table (¡À 0.05V .

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat with Us

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English