Simple analysis of several lead-acid batteries

2022/04/08

  Author :Iflowpower – Portable Power Station Supplier

1, lead-acid battery polar pile ablation, fracture when the lead-acid battery polar pile is ablated, after breaking, the filament method can be repaired. First, the damaged pile is flat from the root, drill 5mm in the center of the cross section, and the hole 15mm is screwed into M6.×Hexagonal screw 30.

Place the tip of the iron on a pole pile, pour it into the heated and melted lead water, and remove the horn tube after cooling. 2, lead-acid battery housing, upper cover crack in driving, if it finds in time, first plug first. The battery is reversed on one side, and the out-drain electrolyte is wiped, and some sealing materials are excavated at the battery cover, and after filling after the exhaust pipe.

If it is a long crack, use the steel saw to saw the V-shaped groove and then make. Adhesive adhesive. The way is to first heat the cracks.

After the soft is soft, cut into a v-shaped slot along the crack, then put the matching resin gel in the repair, follow the paper, put it in the indoor self-hardening be usable. 3, lead-acid battery polar plate vulcanized lead-acid battery polar plate vulcanized, multi-factible battery is in a discharge or semi-discharge state, and causes a lead-granulated pair of thiramidal ps. If the vulcanization is not serious, the active material is restored by the method of charging the small current long time.

The operation method is as follows: First put the battery at 20H discharge rate, pour all the electrolyte, flush with distilled water several times, then inject distilled water to standard liquid surface. Charging the charging current in the second stage of the initial charging, and measure the density of the electrolyte at any time, stop charging when the density is increased to 1.15g / cm3.

Then fell out all the electrolyte in each monobi, then inject distilled water, continue charging. So repeated multiple times, until the density of the electrolyte no longer increase. Finally, the discharge is performed, and then it is fully charged, and the electrolyte density is adjusted to the desired value.

The battery after the charging of vulcanization should be restored to more than 80% of the rated capacity. Otherwise, several times will be made, discharge resolution. 4, the active substance of the lead-acid battery of the lead-acid battery is not out of time, and the precipitate can be removed.

5, the sealing glue of the lead-acid battery is broken when the lead-acid battery is broken, if the crack is small, the iron iron is available. If the crack is large, when the electrolyte leaks, it should be eradicated and re-poured. In order to make the sealing material and the housing reliably, the casting should be wound with cotton yarn.

6. If the lead-acid battery is disconnected, if a single single-handed circuit of the lead-acid battery can be temporarily used. 7.

This phenomenon of lead-acid battery polar plate short circuit is short-circuited by the lead-acid battery polar plate due to too much separator or the bottom deposits. If the partition is damaged, the battery should be removed and the separator is replaced. If only a single partition is damaged, this single-style polar group can be repaired separately.

If there are too many deposits, the electrolyte should be poured, and the dry and clean after drying with distilled water.

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat with Us

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English